Cirrus-logic CS5460A User Manual Page 24
- Page / 54
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CS5460A
24 DS487F5
pulse, one of the output pins (either EOUT or ED-
IR) changes state. When the CS5460A must issue
another energy pulse, the other output changes
state. The direction the motor will rotate is deter-
mined by the order of the state changes. When en-
ergy is positive, EOUT
will lead EDIR such that the
EOUT
pulse train will lead the EDIR pulse train by
~1/4 of the periods of these two pulse train signal.
When energy is negative, EDIR
will lead EOUT in
a similar manner. See Figure 12.
3.3 Auto-boot Mode Using EEPROM
The CS5460A has a MODE pin. When the MODE
pin is set to logic low, the CS5460A is in normal op-
erating mode, called host mode. This mode de-
notes the normal operation of the part, that has
been described so far. But when this pin is set to
logic high, the CS5460A auto-boot mode is en-
abled. In auto-boot mode, the CS5460A is config-
ured to request a memory download from an
external serial EEPROM. The download sequence
is initiated by driving the RESET
pin to logic high.
Auto-boot mode allows the CS5460A to operate
without the need for a microcontroller. Note that if
the MODE pin is left unconnected, it will default to
logic low because of an internal pull-down on the
pin.
3.3.1 Auto-boot Configuration
Figure 13 shows the typical connections between
the CS5460A and a serial EEPROM for proper au-
to-boot operation. In this mode, CS
and SCLK are
driven outputs. SDO is always an output. During
the auto-boot sequence, the CS5460A drives CS
low, provides a clock output on SCLK, and drives
out-commands on SDO. It receives the EEPROM
data on SDI. The serial EEPROM must be pro-
grammed with the user-specified commands and
register data that will be used by the CS5460A to
change any of the default register values (if de-
sired) and begin conversions.
Figure 13 also shows the external connections that
would be made to a calibrator device, such as a PC
EOUT
EDIR
Positive Energy Negative Energy
...
...
...
...
Figure 12. Stepper Motor Format on EOUT and EDIR
CS5460A
EEPROM
/EOUT
/EDIR
MODE
SCK
SDI
SDO
/CS
SCK
SO
SI
/CS
Connector to
Calibrator
VD+
5 K
5 K
Mech. Counter
Stepper Motor
or
Figure 13. Typical Interface of EEPROM to CS5460A
- Features 1
- Description 1
- TABLE OF CONTENTS 2
- LIST OF FIGURES 4
- LIST OF TABLES 4
- ANALOG CHARACTERISTICS 5
- 5V DIGITAL CHARACTERISTICS 7
- 3.3 V DIGITAL CHARACTERISTICS 8
- ABSOLUTE MAXIMUM RATINGS 8
- SWITCHING CHARACTERISTICS 9
- 10 DS487F5 10
- DS487F5 11 11
- 12 DS487F5 12
- 2.2 Performing Measurements 13
- Gain (dB) 14
- Configurations 16
- (just like voltage input) 17
- NOTE: Current channel 17
- 18 DS487F5 18
- DS487F5 19 19
- 20 DS487F5 20
- 3. FUNCTIONAL DESCRIPTION 21
- 3.1 Pulse-Rate Output 21
- Counter Format 22
- 3.2.1 Normal Format 22
- DS487F5 23 23
- Connector to 24
- Calibrator 24
- DS487F5 25 25
- 26 DS487F5 26
- DS487F5 27 27
- ±250 mV on both input 27
- ±50 mV.) 27
- 3.8.3 Calibration Sequence 28
- DS487F5 29 29
- (DC or AC) 30
- 3.9 Phase Compensation 31
- 3.11 Power Offset Register 32
- DS487F5 33 33
- 3.13 Input Filtering 34
- DS487F5 35 35
- 36 DS487F5 36
- DS487F5 37 37
- 3.15 Improving RFI Immunity 38
- 3.16 PCB Layout 38
- 4. SERIAL PORT OVERVIEW 38
- 4.1 Commands (Write Only) 39
- 4.1.1 Start Conversions 39
- 4.1.2 SYNC0 Command 39
- 4.1.3 SYNC1 Command 39
- 4.1.4 Power-Up/Halt 39
- 4.1.5 Power-Down 40
- 4.1.6 Calibration 40
- 4.1.7 Register Read/Write 41
- 4.2 Serial Port Interface 42
- 4.3 Serial Read and Write 42
- 4.3.1 Register Write 42
- 4.3.2 Register Read 42
- 4.4 System Initialization 42
- 4.6 CS5460A Power States 43
- 5. REGISTER DESCRIPTIONS 44
- 5.4 Cycle Count Register 46
- 5.9 Power Offset Register 48
- 5.12 Control Register 50
- 6. PIN DESCRIPTIONS 51
- 24L SSOP PACKAGE DRAWING 53
- 8. ORDERING INFORMATION 54
- 10. REVISION HISTORY 54
Related products and manuals for Hardware Cirrus-logic CS5460A
Hardware Cirrus-logic AN225 User Manual
(4 pages)
(4 pages)
Hardware Cirrus-logic AN278 User Manual
(4 pages)
(4 pages)
Hardware Cirrus-logic AN202 User Manual
(2 pages)
(2 pages)
Hardware Cirrus-logic AN227 User Manual
(4 pages)
(4 pages)
Hardware Cirrus-logic CS5461A User Manual
(44 pages)
(44 pages)
Hardware Cirrus-logic CDB5460AU User Manual
(38 pages)
(38 pages)
Hardware Cirrus-logic CS5462 User Manual
(16 pages)
(16 pages)
Hardware Cirrus-logic CDB5461AU User Manual
(36 pages)
(36 pages)
Hardware Cirrus-logic AN336 User Manual
(3 pages)
(3 pages)
Hardware Cirrus-logic AN337 User Manual
(2 pages)
(2 pages)
Hardware Cirrus-logic CS5463 User Manual
(46 pages)
(46 pages)
Hardware Cirrus-logic CRD5463PM User Manual
(20 pages)
(20 pages)
Hardware Cirrus-logic CDB5463U User Manual
(38 pages)
(38 pages)
Hardware Cirrus-logic CS5464 User Manual
(46 pages)
(46 pages)
Hardware Cirrus-logic CS5466 User Manual
(16 pages)
(16 pages)
Hardware Cirrus-logic CDB5464U User Manual
(38 pages)
(38 pages)
Hardware Cirrus-logic CDB5466U User Manual
(21 pages)
(21 pages)
Hardware Cirrus-logic CS5467 User Manual
(46 pages)
(46 pages)
Hardware Cirrus-logic CDB5467U User Manual
(38 pages)
(38 pages)
Hardware Cirrus-logic CS5480 User Manual
(70 pages)
(70 pages)
© 2020, manymanuals.com. All rights reserved. | 0.553 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals